Skip to main content
  • Home
  • Services
  • Products
  • Innovations
  • About us
  • 20 years
  • Career
  • Contact
  • CZ
  • EN
  • DE
arrow-up-thick
  • Home
  • Products
  • MQB37W Test Bench
37w1
37w2
37w3
37w4

MQB37W Test Bench

Test benches
The MQB37W Test Bench represents a model of a car electronics where all units can be seated and work the same as usual in cars.

Product Description

The MQB37W Test Bench is mainly intended for supporting the development and testing of MIB3 projects.

The advantage of this solution is that tests can be run without the need for an actual car. The MQB37W Test Bench is made of a lightweight aluminium construction. The structure holds a wired harness fixed in a wire duct, which is intended for the connection of ECUs to evaluate technologies and accessories.

The front side of the test bench offers a place for the installation of ABT, SMLS, KI / FPK and other hardware. Additional units can be installed on the sides of the test bench, where data buses and sockets are located. The power and data terminals are located on the back side. This provides extensibility to the test bench. We offer various accessories for this test bench.

Thanks to the flexibility of the mechanical design and a suitably designed wiring harness, the test state can be easily modified and extended. Custom modifications are also possible.

The MQB37W Test Bench can be made in an online (connected to the backend) or an offline version. The test bench can be extended using an RTL Enabler that allows the user to remotely operate it from any location using a web browser.

Key Features

  • Light and mobile test centre
  • Online version registered to the backend
  • Offline version
  • Optional connection for headphones
  • Construction flexibility
  • Possibility of extension with optional accessories (from a mechanical point of view)
  • Possibility to connect other units and accessories (from a wiring point of view)
  • CAN bus terminal
  • Prepared for RTL Enabler
  • Prepared for CANSim4 Simulator
  • Prepared for MGB FrameGrabber
  • Prepared for PDC Box
  • Prepared for TraceBox
   

 

 

Readiness to Connection

  • Gateway (GW) 
  • Modular infotainment matrix (MIB3)
  • Integrated control panel (ABT)
  • Instrument cluster (IC/FPK)
  • Body control module (BCM)
  • Multi-function steering wheel (MFL)
  • Steering column switch module (SMLS)
  • Start / Stop button
  • USB-C HUB
  • Electronic steering column lock (ELV)
  • Read coil
  • Kessy with antennas
  • Door control module (TSG), locks
  • LINDa (roof module) 
  • Direct access button (DIETa) 
  • Air conditioning (AC)
  • Koppelbox
  • Online connectivity unit (OCU3)
  • Speaker for OCU
  • Lights and vision control panel (LiSi)
  • 4x loudspeakers (2 speakers included)
  • On board diagnostic (OBD II)
  • Rear view camera (RVC eCompact/eSmart)
  • Top view camera eEntry (TVC)
  • Cameras for top view eEntry
  • Head-Up-Display (HUD)
  • Sound (AMP)
  • 3.5 mm jack connector
  • Park Distance Control (PDC/PLA)
   

 

 

Accessories

Power supply Switching power supply 0-16 V / 20 A
CANSim4 Simulation of clamp states, speed, RPM, etc.
MGB FrameGrabber Video capture of IC / FPK, ABT, etc.
RTL Enabler Extends test bench to remotely operate it using a web browser
PDC Box Compact, lightweight, aluminium box for PDC unit and sensors
TraceBox Modular solution for tracing and logging
MSG cable harness Cable harness for connection of the motor control unit
RVC / TVC cable harness Cable harness for connection of RVC / TVC
PDC / PLA cable harness Cable harness for connection of PDC / PLA
Sound box or cable harness for AMP According to customer requirements
ABT holder Aluminium panel for retrofitting
IC / FPK holder Retrofit kit
SMLS holder Aluminium steering wheel module holder (SMLS)
LiSi holder Plastic holder for lights and vision control panel (LiSi)
MFL holder Holder for multi-function steering wheel to on table (not for fixed mounting on the test bench)
LINDa holder Holder for retrofitting the LINDa module
Antenna cables Specific lengths
Antenna holders Panel for retrofitting on the test bench
USB-C HUB holder Holder for USB-C HUB
Other accessories Available upon demand

 

Technical Parameters

Supported platform MQB37W
Main purpose Development and validation of MIB3
Connections CAN, LIN, Ethernet, UART (RS232), OBD II
Power supply 12 V to 15 V
Operating temperature For use in laboratory conditions only
Dimensions (W x D x H) 444 x 590 x 415 mm (including speakers, brackets and DIN rail parts)
Weight without accessories 13.8 kg

Documentation

On request, we offer individual training and professional consultation with this product. For more information, please contact us.

Stažení dokumentů.

Stažení dokumentů je umožněno pouze registrovaným uživatelům. Máte-li svůj účet pak je nutné se přihlásit.

Register
Log in

Leave us message — we will contact you!

Contact form

*
*
*
*
*
*
  • Services
  • Mobility of the future
  • Development at software and system level
  • Testing
  • Products
  • Video Capture
  • Simulators
  • Test stands
  • Test Suitcases
  • Company
  • About us
  • Innovations
  • Career
  • Contact
instagram
facebook
linkedin2
youtube
2022 © By using this website you agree to the use of cookies.
Designed and developed by Freely Agency & H1.cz
  • Personal Data Protection
  • Compliance
  • Terms and conditions