MQB Test Bench
Test benches
MQB Test Bench represents a model of a car electronics where all units can be seated and work as in usual cars
Product Description
Product Description
This test bench is intended mainly for support development and testing of the MIB3 projects.
The advantage of this solution is tests can be run without need for the actual car. MQB Test Bench is made of a light aluminium construction. The construction holds a wired harness. The structure holds a wired harness fixed in a wire duct, which is intended for the connection of ECUs, measuring technologies and accessories.
The front side of the test bench offers a place for the installation of ABT, SMLS, KI / FPK and other HW. Additional units can be installed on the sides of the test bench, where you can also find data buses and sockets. Power and data terminals are located on the back side. This brings a potential of additional extension of the test bench. We offer various accessories for this test bench.
Thanks to the variability of the mechanical design and a suitably designed wiring harness, the test state can be easily modified and extended. Tailor made modifications are possible.
MQB Test Bench can be made in online (connected to backend) or offline version. It is also possible to extend test bench by RTL Enabler that allows user to operate it remotely from everywhere using web browser.
The advantage of this solution is tests can be run without need for the actual car. MQB Test Bench is made of a light aluminium construction. The construction holds a wired harness. The structure holds a wired harness fixed in a wire duct, which is intended for the connection of ECUs, measuring technologies and accessories.
The front side of the test bench offers a place for the installation of ABT, SMLS, KI / FPK and other HW. Additional units can be installed on the sides of the test bench, where you can also find data buses and sockets. Power and data terminals are located on the back side. This brings a potential of additional extension of the test bench. We offer various accessories for this test bench.
Thanks to the variability of the mechanical design and a suitably designed wiring harness, the test state can be easily modified and extended. Tailor made modifications are possible.
MQB Test Bench can be made in online (connected to backend) or offline version. It is also possible to extend test bench by RTL Enabler that allows user to operate it remotely from everywhere using web browser.
Key Features
- Light and mobile test center
- Online version registered to backend
- Offline version
- Possibility to connect headphones
- Construction variability
- Possibility of extension with optional accessories (from the mechanical point of view)
- Possibility to connect other units and accessories (from the wiring point of view)
- CAN bus terminal
- Prepared for RTL Enabler
- Prepared for CANSim4 Simulator
- Prepared for MGB FrameGrabber
- Prepared for PDC Box
- Prepared for TraceBox
Readiness to Connection
- Modular Infotainment Matrix (MIB3)
- Gateway (GW)
- Integrated control panel (ABT)
- Instrument Cluster (IC/FPK)
- Body Control Module (BCM)
- Multi-function steering wheel (MFL)
- Steering column switch module (SMLS)
- USB-A HUB
- Read coil
- Kessy including antennas
- Door control module (TSG), Locks
- 3 - Tasten Modul (3TM)
- Air Conditioning (AC)
- MiKo bar (PDC/PLA/FPA buttons)
- Online Connectivity Unit (OCU3)
- Speaker for OCU
- Rotary light switch (LDS)
- Microphone (MIC)
- 4x Loudspeaker (2 speakers included)
- On Board Diagnostic (OBD II)
- Rear View Camera (RVC Low/Compact/Compact+)
- Area View (AV) – without cameras
- Head-Up-Display (HUD)
- Sound (AMP)
- 3,5 mm jack connector
- Park Distance Control (PDC/PLA)
Accessories
| Power supply | Switching power supply 0-16 V / 20 A |
| CANSim4 | Simulation of clamps state, speed, RPM etc. |
| MGB FrameGrabber | Grabbing of IC / FPK, ABT etc. |
| RTL Enabler | Extender for possibility to operate test bench remotely using web browser |
| PDC Box | Compact, lightweight, aluminium box for PDC unit and sensors |
| TraceBox | Modular solution for tracing |
| MSG cable harness | Cable harness for connection of motor control unit |
| RVC / AV cable harness | Cable harness for connection of RVC / AV |
| PDC / PLA cable harness | Cable harness for connection of PDC / PLA |
| Sound box or cable hanress for AMP | According to customer requirements |
| ABT holder | Aluminium panel for retrofitting |
| IC / FPK holder | Retrofit kit |
| SMLS holder | Aluminium steering wheel module holder (SMLS) |
| LDS holder | Aluminium rotary light switch holder (LDS) |
| MFL holder | Holder for multi-function steering wheel to the table (not for fixed mounting to the test bench) |
| 3TM holder | Bracket for retrofitting the 3TM module |
| MIC holder | Aluminium holder for retrofitting the microphone |
| MiKo bar (MiKo toolbar) holder | Holder for retrofitting MiKo rails (PDC/PLA/FPA buttons) |
| Antennas cables | Specific lengths |
| Atennas holders | Panel for retroffiting on the test bench |
| Original parts and components | Units, controls, switches, antennas, speakers etc. |
| Other accessories | On demand |
Technical Parameters
| Supported platforms | MQB |
| Main purpose | Development and validation MIB3 |
| Connection | CAN, LIN, Ethernet, UART (RS232), OBD II |
| Power supply | 12 V – 15 V |
| Operating temperature | For use in laboratory conditions only |
| Dimensions (W x D x H) | 444 x 590 x 415 mm (including speakers, brackets and DIN rail parts) |
| Weight without accessories | 13,8 kg |
On request, we offer individual training and professional consultation with this product. For more information, please contact us.
Leave us message — we will contact you!
Contact form
2020 © By using this website you agree to the use of cookies.
Designed and developed by Freely Agency & H1.cz
Designed and developed by Freely Agency & H1.cz