Skip to main content
  • Hauptmenü
  • Dienstleistungen
  • Produkte
  • Innovationen
  • Über uns
  • 20 Jahre
  • Karriere
  • Kontakte
  • CZ
  • EN
  • DE
arrow-up-thick
  • Home
  • Produkte
  • Produkte
  • PWM & CAN Generator
PWM & CAN Generator
PWM & CAN Generator
PWM & CAN Generator
PWM & CAN Generator

PWM & CAN Generator

Simulatoren
The PWM and CAN Generator combines the simulations of signals needed for OCU stimulation. It consists of two parts – a PWM simulator and a CAN simulator.

Produktbeschreibung

The PWM & CAN Generator consists of two parts - a PWM simulator and a CAN simulator.

The PWM simulator generates a “No Crash” PWM signal, a “Crash” PWM signal, and no PWM signal. The CAN simulator generates signals for clamps, dimming, vehicle speed, and airbag crashes.

Hauptmerkmale

  • Small size and simple operation
  • Covers frequencies of 10 Hz and 100 Hz
  • LED indication of CAN communication
  • Actual values or states of the generated signals displayed on a 4.3” colour LCD display

 

 

 

 

   

 

 

PWM Simulator

  • The PWM Simulator generates defined PWM signal states, such as an airbag unit.
  • It generates the following states: “No Crash” PWM signal, “Crash” PWM signal, and no PWM signal.
  • For the “Crash” PWM signal, it is possible to set 3 levels: Crash Level 1, Crash Level 2, and Crash Level 3 (differing in cycle times).
  • The PWM signal level is selected using a three-position switch.
  • It meets the VW80105-93 and LAH.DUM.959.E requirements.

 

 

 

   

 

 

CAN Simulator

Generates signals for: 

 

  • KL.S, KL.15
  • KL.58 (dimming)
  • Vehicle speed
  • Airbag_01 airbag crash signal (only the states 0-kein_Crash, 1-Crash_Intensitaet_1, 7-Crash_Intensitaet_3)
   

 

 

Technische Daten und Schnittstellen

  • Three crash levels (Level 1 60 ms / 40 ms, Level 2 40 ms / 60 ms, Level 3 20 ms / 80 ms)
  • D-SUB 9 male connector with CAN signals 
  • 6-pin connector with non-CAN signals 
  • CAN termination – The termination resistors can be connected or disconnected from Antrieb and Fahrwerk CAN via the CAN term switch (The termination resistor is permanently connected to a high-speed Comfort CAN.)
   

 

 

Technische Daten

Unterstützte Plattformen PQ, MQB
Frequenz 10 Hz und 100 Hz
LCD-Display 4,3"
Stromversorgung 8 V – 18 V
Betriebstemperatur -20 °C – 70 °C bei der Verhinderung von Kondensation
Abmessungen (B x T x H) 165 x 165 x 30 mm (einschließlich Anschlüsse und Bedienelemente)
Gewicht 650 g

Dokumentation

Auf Anfrage bieten wir Ihnen eine individuelle Schulung und profesionelle Beratung zu diesem Produkt an. Für weitere Informationen kontaktieren Sie uns.
Produktblatt 380.16 KB, pdf Download

Stažení dokumentů.

Stažení dokumentů je umožněno pouze registrovaným uživatelům. Máte-li svůj účet pak je nutné se přihlásit.

Registrovat
Einloggen

Kontaktieren Sie uns - wir melden uns bei Ihnen!

Kontaktformular

*
*
*
*
*
*
  • Dienstleistungen
  • Zukunftsmobilität
  • Entwicklung auf Software- und Systemebene
  • Testen
  • Produkte
  • Grabbing-Technik
  • Simulatoren
  • Teststände
  • Testkoffer
  • Firma
  • Über uns
  • Innovationen
  • Karriere
  • Kontakte
instagram
facebook
linkedin2
youtube
2022 2019 © Digiteq Automotive s.r.o. Durch das Nutzen dieser Webseiten geben Sie Ihr Einverständnis damit, dass Cookie-Dateien verwendet werden.
Webseitenkreierung Freely Agency & H1.cz
  • Schutz personenbezogener Daten
  • Compliance
  • Geschäftsbedingungen